我廠出產的單板烘干設備可選熱源以下幾種：蒸汽導熱、熱風導熱、熱油導熱,干燥廢木料導熱，電加熱。使用以上三種熱載體加熱熱風幕（熱風導熱在外），并使用與風幕相連的離心式風機，使之變成熱風，再經由風箱、風管、噴吹到單板的上下兩面，使單板受熱均勻，使之到達枯燥的意圖。本廠出產的單板枯燥機選用鏈條傳動上下輥相對同步工作，靠上輥的自重揉捏單板運轉，枯燥出的單板平整度好，出產率高，可加工厚度0.8mm～8mm的單板，具有運轉平穩，操作簡便，熱效率高等長處。

    二、使用注意事項：1、木皮烘干機進入現場，須由專業人員對接，裝置根底水平面上，水平差錯應控制在正負3mm以內，如在使用過程中，發現根底有沉隆，拱起應及時停機查看，測驗水平，避免對機器傳動部分形成損壞。2、單板烘干機縱向由進料口進入機內，進口入料時要擺正，使單板與傳動輥成90°入料聯接要好，單板在烘干之前應剪切整齊在進行烘干，避免塞車。3、烘干后的單板要嚴厲把握好含水量，依據用戶烘干單板含水量，要求自行調理調速電力的轉速。0.6mm以下的單板烘干機內溫度一般應為110℃～130℃之間，轉數應控制在1000轉/分～1200轉/分，單板厚度在0.8mm以上，烘干機內溫度應在150℃～170℃之間，轉速為800轉/分～900轉/分。正常含水量為8～10個水。烘干后的單板若為6個水以下的含水量，則單板外表的平整度不好，應屬正常現象，與設備自身無關（注：以上數據僅供參考，用戶可依據自行的出產需求進行調整）。 三、保護與保養：1、木皮烘干機的風機高轉速風機，風機軸承應每月注滑油一次，加注耐高溫黃干油（蓋達牌300℃）。2、傳動鏈條應每3～4天滴注一次，耐高溫機油。3、上下傳動輥應每月鏟除一次粉塵，避免粉塵堆積過厚，形成塞車、跑偏現象。4、主傳動減速機應每三個月查看一次機油，如發現機油蛻變或短少應及時替換或補充。